Atmega Fuse Repair Programmer

View a demonstration video here

OUR BEST SELLER! Don't throw away your locked avr's! Simply unlock them with this easy to use device. This device is an avr HIGH VOLTAGE PARALLEL programmer that is designed to program all fuses, no matter what may have been previously programmed. If you mistakenly programmed the RSTDISBL fuse, disabled the SPIEN fuse, or programmed the wrong values in the CKSEL fuses, NO PROBLEM! Simply insert any avr from device list below and connect power. Within one second, fuses will be restored to factory settings. 

Now Three modes of operation. Mode 1 allows code to be preserved while fuses are restored to factory settings. (lock bits must not be programmed) 

Mode 2 simply restores fuses to factory settings even if the lock bits have been programmed (Code will be erased) 

***Mode 3 (advanced mode) allows writing of any fuse value for any avr device that uses High Voltage Parallel Programming mode, even if device is not in the device list below.  Now better than ever, Mode 3 will support many more devices including the older mature avr's!

Needs no computer!*** Once fuses are restored to factory settings, you can program the avr using your favorite ISP programmer and software. 

This programmer pays for itself in just a few uses. If you have half a dozen atmega's or attiny devices that have been programmed incorrectly, simply restore them all in just a few minutes. No need to spend money to replace the avr's!

This programmer is not designed to extract code from a device where the lock bits have been programmed! Please do not ask.

Supports over 78 AVR devices (see below)

*** Computer can be connected to debug port  on programmer using the RS232 to TTL Converter or the USB2TTL (not included) if you want to access advanced mode. This is only necessary in order to access advanced mode (mode3). Green LED indicates success, Yellow LED indicates error programming fuses. It's that easy!

YOU MUST USE A POWER SUPPLY THAT EXCEEDS 13.5 VDC positive center (not included) to ensure reliability in programming. Instructions will be included with purchase. It is a good idea to measure your power supply to ensure correct voltage and polarity.

Supported Devices for Atmega Fuse Repair Programmer
**** (All pins must be wired directly to the socket)

Socket #1

ATmega16
ATmega16L
ATmega32
ATmega32L
ATmega161
ATmega161L
ATmega164
ATmega164A
ATmega164P
ATmega164V
ATmega164PV
ATmega164PA
ATmega324
ATmega324A
ATmega324P
ATmega324PA
ATmega324V
ATmega644
ATmega644A
ATmega644P
ATmega644V
ATmega644PA
ATmega644PV
ATmega8535
ATmega8535L
ATmega1284
ATmega1284P

Socket #2

ATtiny2313
ATtiny2313A
ATtiny2313V
ATtiny4313

The following
devices are
supported, however
they must
be wired to any
socket.
ATtiny43U****
ATtiny87****
ATtiny88****
ATtiny167****

Socket #3

ATmega8515
ATmega8515L
Atmega128****
ATmega162
ATmega162V

Socket #4

ATmega8
ATmega8A
ATmega8L
ATmega48
ATmega48A
ATmega48V
ATmega48P
ATmega48PA
ATmega48PV
ATmega88
ATmega88A
ATmega88P
ATmega88PA
ATmega88V
ATmega88PV
ATmega164
ATmega164A
ATmega164P
ATmega164PA
ATmega168
ATmega168A
ATmega168V
ATmega168P
ATmega168PA
ATmega168PV
ATmega328P
ATmega328PV

Socket #5

ATtiny26
ATtiny26L
ATtiny261
ATtiny261A
ATtiny261V
ATtiny461
ATtiny461A
ATtiny461V
ATtiny861
ATtiny861A
ATtiny861V

If the atmega or attiny device is not in the list above, you can reprogram the fuses by accessing advanced mode as long as the device supports High Voltage Parallel Programming mode. You will need a TTL to RS232 converter or a TTL to USB converter to access advanced mode.

$29.00 US 


Purchase both programmers Atmega Fuse Repair Programmer and ATTiny Fuse Repair Programmer for only $49.00 US
When ordering this programmer, you can purchase the low cost USB ISP Programmer for only $10 more.

Order the ATMEGA Fuse Repair Programmer &  Low Cost USB AVR Programmer together:

Back to homepage

ATTiny Fuse Repair Programmer

This programmer is an ATTINY HIGH VOLTAGE SERIAL Programmer. Since it uses the High Voltage serial programming method, this device will restore ALL fuses to factory settings regardless of the current state of the fuses. Simply plug your ATTiny into the correct socket, and apply power. Within one second, the fuses will be restored to factory ATMEL configuration allowing you to reprogram the ATtiny with your favorite ISP software. A convenient tool to have! 

This programmer pays for itself in just a few uses. If you have half a dozen ATtiny devices that have been programmed incorrectly, simply restore them all in just a few minutes. No need to spend money to replace the avr's!

Now Three modes of operation. Mode 1 allows code to be preserved while fuses are restored to factory settings. (lock bits must not be programmed) 

Mode 2 simply restores fuses to factory settings even if the lock bits have been programmed (Code will be erased) 

***Mode 3 (advanced mode) allows writing of any fuse value even if device is not in the device list below. Now better than ever, Mode 3 will support many more devices including the older mature avr's!

Needs no computer!*** Once fuses are restored to factory settings, you can program the avr using your favorite ISP programmer and software. 

This programmer pays for itself in just a few uses. If you have half a dozen atmega's or attiny devices that have been programmed incorrectly, simply restore them all in just a few minutes. No need to spend money to replace the avr's!

This programmer is not designed to extract code from a device where the lock bits have been programmed! Please do not ask.

Supports the devices in the list below.

*** Computer can be connected to debug port  on programmer using the RS232 to TTL Converter or the USB2TTL (not included) if you want to access advanced mode. This is only necessary in order to access advanced mode (mode3). Green LED indicates success, Yellow LED indicates error programming fuses. It's that easy!

YOU MUST USE A POWER SUPPLY THAT EXCEEDS 13.5 VDC positive center (not included) to ensure reliability in programming. Instructions will be included with purchase. It is a good idea to measure your power supply to ensure correct voltage and polarity.

Supported Devices for ATTiny Fuse Repair Programmer

Socket #1 

ATtiny12
ATtiny12V
ATtiny12L
ATtiny13
ATtiny13A
ATtiny13V
ATtiny25
ATtiny25V
ATtiny45
ATtiny45V
ATtiny85
ATtiny85V

Socket #2

ATtiny24
ATtiny24A
ATtiny24V
ATtiny44
ATtiny44A
ATtiny44V
ATtiny84
ATtiny84A
ATtiny84V

$25.00 US

Purchase both programmers Atmega Fuse Repair Programmer and ATTiny Fuse Repair Programmer for only $49.00 US
When ordering this programmer, you can also purchase the low cost USB ISP Programmer for only $10 more. 

   Order the ATtiny Fuse Repair Programmer &  Low Cost USB AVR Programmer together:

Back to homepage

© 2011, microcontrollerprog.com