|
|
Atmel
Programmers
|
|
|
Atmel
Programmers
|
Welcome to our website! We are a small company trying to keep prices
as low as possible on all products. We don't believe in fancy websites.
More important is honest, customer service, support and low prices.
We always try to answer email as promptly as possible.
Please visit the testimonials page to read what our customers have to say about us.
Atmega Fuse Repair Programmer
 |
OUR BEST SELLER! Don't throw away your locked avr's! Simply unlock them with this easy to use device. This device is an avr HIGH VOLTAGE PARALLEL programmer that is designed to program all fuses, no matter what may have been previously programmed. If you mistakenly programmed the RSTDISBL fuse, disabled the SPIEN fuse, or programmed the wrong values in the CKSEL fuses, NO PROBLEM! Simply insert any avr from device list below and connect power. Within one second, fuses will be restored to factory settings. Now Three modes of operation. Mode 1 allows code to be preserved while fuses are restored to factory settings. (lock bits must not be programmed) Mode 2 simply restores fuses to factory settings even if the lock bits have been programmed (Code will be erased) ***Mode 3 (advanced mode) allows writing of any fuse value even if device is not in the device list below. Now better than ever, Mode 3 will support many more devices including the older mature avr's! Needs no computer!*** Once fuses are restored to factory settings, you can program the avr using your favorite ISP programmer and software. This programmer pays for itself in just a few uses. If you have half a dozen atmega's or attiny devices that have been programmed incorrectly, simply restore them all in just a few minutes. No need to spend money to replace the avr's! This programmer is not designed to extract code from a device where the lock bits have been programmed! Please do not ask. Supports 45 AVR devices (see below) *** Computer can be connected to debug port on programmer using the RS232 to TTL Converter or the USB2TTL below (not included) if you want to access advanced mode. This is only necessary in order to access advanced mode (mode3). Green LED indicates success, Yellow LED indicates error programming fuses. It's that easy! YOU MUST USE A POWER SUPPLY THAT EXCEEDS 13.5 VDC positive center (not included) to ensure reliability in programming. Instructions will be included with purchase. It is a good idea to measure your power supply to ensure correct voltage and polarity. |
Supported Devices for Atmega Fuse Repair Programmer
**** (All SMD pins must be wired directly to the socket)
|
Socket #1 ATmega16 |
Socket #2 ATtiny2313
|
Socket #3 ATmega8515 |
Socket #4 ATmega8 |
Socket #5
ATtiny26 |
$29.00 US
When ordering this programmer, you can purchase the low cost USB ISP Programmer for only $10 more (with free shipping). See below.
Questions? Click HERE to send email
ATTiny Fuse Repair Programmer
|
|
This programmer is an ATTINY HIGH VOLTAGE SERIAL Programmer. Since it uses the High Voltage serial programming method, this device will restore ALL fuses to factory settings regardless of the current state of the fuses. Simply plug your ATTiny into the correct socket, and apply power. Within one second, the fuses will be restored to factory ATMEL configuration allowing you to reprogram the ATtiny with your favorite ISP software. A convenient tool to have! This programmer pays for itself in just a few uses. If you have half a dozen ATtiny devices that have been programmed incorrectly, simply restore them all in just a few minutes. No need to spend money to replace the avr's! Two modes of operation. Mode 1 allows code to be preserved while fuses are restored to factory settings. (lock bits must not be programmed) Mode 2 (default setting) simply restores fuses to factory settings even if the lock bits have been programmed (Code will be erased) This programmer is not designed to extract code from a device where the lock bits have been programmed! Please do not ask. Supports the devices in the list below. |
Supported Devices for ATTiny Fuse Repair Programmer
|
Socket #1 ATtiny12 |
Socket #2
ATtiny24 |
$25.00 US
When ordering this programmer, you can purchase the low cost USB ISP Programmer for only $10 more (with free shipping). See below.
Questions? Click HERE to send email
USB to TTL Converter
|
|
|
USB to TTL converter for the above two Fuse Repair Programmers. Use this converter to display results in terminal when repairing fuses or in Mode 3 (Advanced Mode). Unit takes power from USB port, no need to connect power to programmer. Can also be used for any microcontroller running at 3 - 5 Volts. Comes with drivers for windows. The easiest way to connect your microcontroller to the USB port. Will work with Windows 98,Windows XP, Vista & Windows7. |
$9.99 US
Questions? Click HERE to send email
RS232 to TTL Converter
|
|
RS232 to TTL converter for the above two Fuse Repair Programmers. Use this converter to display results in terminal when repairing fuses. Unit takes power from programmer. Can also be used for any microcontroller running at 3 - 5 Volts. |
$9.99 US
Questions? Click HERE to send email
Low Cost AVR USB Programmer
|
|
The low cost usb avr programmer takes power from your circuit. This programmer will work on either 3V or 5V circuits. Can be used with avrdude. Comes with standard 10 pin ISP cable. |
Supported Devices for the Low Cost AVR USB Programmer
|
ATtiny12 |
ATmega168 |
We are trying to keep the cost as low as possible, Only $15.00 US!
Questions? Click HERE to send email
AVR/89S51/89S52 USB Programmer
|
|
This low cost programmer is powered from the usb port and also supplies 5V power to your circuit. The programmer can be used with avrstudio, avrdude or avrprog (avr910usb). **Please specify when ordering which programmer configuration you require**. If you order the avrisp Configuration, the programmer will not support AT89S devices. Comes with standard 10 pin ISP cable. |
Supported Devices for AVR USB Programmer
|
AVRASP Programmer Configuration
|
ATmega162 |
AVRISP Configuration All of the devices on the left EXCEPT the 89S Devices.
|
The avr910 USB programmer will work with avrprog.exe (within AVRStudio) and avrdude.exe
Supported Devices for AVR910 USB Programmer:
|
AT89S51 **** |
Additional devices when used with avrdude: |
**** Not supported with avrdude. Select device AT89S53 in avrprog.exe.
We are trying to keep the cost as low as possible, Only $20.00 US!
***To AVOID A DELAY in your order, Please select the correct shipping method from the drop
down list before clicking "Buy Now" button.
If you are not in Canada or the USA, Please select International Shipping.***
Questions? Click HERE to send email
AVR Standalone ISP Programmer
 |
This device will program any avr (in the
device list below) without the use of a computer.**** Power can either
be supplied by the target (as low as 3 VDC) or directly using a 9VDC
power adapter with positive center (not included). This can easily be
changed using a simple jumper setting (J3). Standalone operation is
invoked when jumper J2 is installed.
**** A computer is required to load the hex file to the memory, (up to 31K flash file, 1K eeprom) Once loaded, the file remains in memory and the unit will perform as a standalone unit. Connection can be made through a 9 pin straight through serial cable (not included) to any serial port. If your computer does not have a serial port, our USB to Serial cable (below) has been tested works well with this programmer. Any terminal program can be used to upload the hex file. For best results, download Tera Term here, and follow the instructions on setting up the terminal carefully (instructions are included with the purchase of the programmer). |
Supported Devices for AVR Standalone ISP Programmer
*** Limited to 32K including eeprom file
|
ATmega Devices |
ATtiny
Devices |
$29.00 US
Questions? Click HERE to send email
AT89S Standalone ISP Programmer
|
|
NEW Devices just added to the list below! If you are fed up with unreliable parallel port programmers, this programmer is the one you want. This programmer will program the devices in the list below without the use of a computer.**** Files to be programmed are stored in the programmer's memory. Programmer takes power from the target (5V) or uses it own power from a 9VDC power adapter with positive center (not included). This can easily be changed using a simple jumper setting (J3). Standalone operation is invoked when jumper J2 is installed. Perfect for programming off site without having to bring your computer, programmer, cables and power supply. This is the most reliable method for programming AT89 devices in ISP mode! Similar to the above avr programmer, except this one programs the 8051 devices in circuit listed below: AT89S2051 More devices will be included in the very near future. FREE** upgrades are included in the price. **Shipping cost is not covered with updates/upgrades.** **** A computer is required to load the hex file to the memory, (up to 12K flash file, 2K eeprom) Once loaded, the file remains in memory and the unit will perform as a standalone unit. Connection can be made through a 9 pin straight through serial cable (not included) to any serial port. Any terminal program can be used to upload the hex file. For best results, download Tera Term here, and follow the instructions on setting up the terminal carefully (instructions are included with the purchase of the programmer). If your computer does not have a serial port, our USB to Serial cable (below) has been tested works well with this programmer. |
$29.00 US
|
Programmer Including Shipping |
|
***To AVOID A DELAY in your order, Please select the correct shipping method from the drop |
Questions? Click HERE to send email
USB to Serial Cable
|
|
These days, most NEW computers (especially laptops) are not equipped with a serial port. This device converts a USB2.0 port into an RS232 port. Tested and working reliably in Windows XP, and Vista. Drivers included for both operating systems. We tested this cable on all of the programmers listed above and it works perfectly! |
$9.99 US
Questions? Click HERE to send email
